138 lines
4.4 KiB
Plaintext
138 lines
4.4 KiB
Plaintext
## Configuration file for CAVA. Default values are commented out. Use either ';' or '#' for commenting.
|
|
|
|
|
|
[general]
|
|
|
|
# Smoothing mode. Can be 'normal', 'scientific' or 'waves'.
|
|
; mode = normal
|
|
|
|
# Accepts only non-negative values.
|
|
framerate = 60
|
|
|
|
# 'autosens' will attempt to decrease sensitivity if the bars peak. 1 = on, 0 = off
|
|
# 'overshoot' allows bars to overshoot (in % of terminal height) without initiating autosens.
|
|
; autosens = 1
|
|
; overshoot = 20
|
|
|
|
# Manual sensitivity in %. Autosens must be turned off for this to take effect.
|
|
# 200 means double height. Accepts only non-negative values.
|
|
; sensitivity = 100
|
|
|
|
# The number of bars (0-200). 0 sets it to auto (fill up console).
|
|
# Bars' width and space between bars in number of characters.
|
|
bars = 0
|
|
bar_width = 1
|
|
bar_spacing = 0
|
|
|
|
|
|
# Lower and higher cutoff frequencies for lowest and highest bars
|
|
# the bandwidth of the visualizer.
|
|
# Note: there is a minimum total bandwidth of 43Mhz x number of bars.
|
|
# Cava will automatically increase the higher cutoff if a too low band is specified.
|
|
; lower_cutoff_freq = 50
|
|
; higher_cutoff_freq = 10000
|
|
|
|
|
|
|
|
[input]
|
|
|
|
# Audio capturing method. Possible methods are: 'pulse', 'alsa' or 'fifo'.
|
|
# Defaults to 'pulse', 'alsa' or 'fifo', in that order, dependent on what support cava was built with.
|
|
#
|
|
# All input methods uses the same config variable 'source'
|
|
# to define where it should get the audio.
|
|
#
|
|
# For pulseaudio 'source' will be the source. Default: 'auto', which uses the monitor source of the default sink
|
|
# (all pulseaudio sinks(outputs) have 'monitor' sources(inputs) associated with them).
|
|
#
|
|
# For alsa 'source' will be the capture device.
|
|
# For fifo 'source' will be the path to fifo-file.
|
|
; method = pulse
|
|
; source = auto
|
|
|
|
; method = alsa
|
|
; source = hw:Loopback,1
|
|
|
|
; method = fifo
|
|
; source = /tmp/mpd.fifo
|
|
|
|
|
|
|
|
[output]
|
|
|
|
# Ouput method. Can be 'ncurses', 'noncurses' or 'raw'.
|
|
# 'noncurses' is for systems that does not suport ncurses.
|
|
# 'raw' is a 16 bit data stream of the bar heights that can be used to send to other applications.
|
|
# 'raw' defaults to 200 bars, which can be adjusted in the 'bars' option above.
|
|
; method = raw
|
|
|
|
# Visual styles. Can be 'stereo' or 'mono'.
|
|
# 'stereo' mirrors both channels with low frequencies in center.
|
|
# 'mono' averages both channels and outputs left to right lowest to highest frequencies.
|
|
style = mono
|
|
|
|
# Raw output target. A fifo will be created if target does not exist.
|
|
; raw_target = /dev/stdout
|
|
|
|
# Raw data format. Can be 'binary' or 'ascii'.
|
|
; data_format = binary
|
|
|
|
# Binary bit format, can be '8bit' (0-255) or '16bit' (0-65530).
|
|
; bit_format = 16bit
|
|
|
|
# Ascii max value. In 'ascii' mode range will run from 0 to value specified here
|
|
; ascii_max_range = 1000
|
|
|
|
# Ascii delimiters. In ascii format each bar and frame is separated by a delimiters.
|
|
# Use decimal value in ascii table (i.e. 59 = ';' and 10 = '\n' (line feed)).
|
|
; bar_delimiter = 59
|
|
; frame_delimiter = 10
|
|
|
|
|
|
|
|
[color]
|
|
|
|
# Colors can be one of seven predefined: black, blue, cyan, green, magenta, red, white, yellow.
|
|
# Or defined by hex code '#xxxxxx' (hex code must be within ''). User defined colors requires a
|
|
# terminal that can change color definitions such as Gnome-terminal or rxvt.
|
|
; background = black
|
|
foreground = white
|
|
|
|
# Gradient mode, only hex defined colors are supported, background must also be defined in hex
|
|
# or remain commented out. 1 = on, 0 = off. Warning: for certain terminal emulators cava will
|
|
# not able to restore color definitions on exit, simply restart your terminal to restore colors.
|
|
gradient = 1
|
|
gradient_color_1 = '#ea4230'
|
|
gradient_color_2 = '#820bc6'
|
|
|
|
|
|
|
|
[smoothing]
|
|
|
|
# Multiplier for the integral smoothing calculations. Takes values from 0-0.99.
|
|
# Higher values means smoother, but less precise. Set to 0 to disable.
|
|
; integral = 0.7
|
|
|
|
# Disables or enables the so-called "Monstercat smoothing". Set to 0 to disable.
|
|
; monstercat = 0
|
|
|
|
# Set gravity multiplier for "drop off". Higher values means bars will drop faster.
|
|
# Accepts only non-negative values. 0.5 means half gravity, 2 means double. Set to 0 to disable "drop off".
|
|
; gravity = 1
|
|
|
|
|
|
# In bar height, bars that would have been lower that this will not be drawn.
|
|
; ignore = 0
|
|
|
|
|
|
[eq]
|
|
|
|
# This one is tricky. You can have as much keys as you want.
|
|
# Remember to uncomment more then one key! More keys = more precision.
|
|
# Look at readme.md on github for further explanations and examples.
|
|
; 1 = 1 # bass
|
|
; 2 = 1
|
|
; 3 = 1 # midtone
|
|
; 4 = 1
|
|
; 5 = 1 # treble
|